Dating clock hands

Even the type of material used to construct your antique clock movement how help, or discovering when chimes were introduced and the type hands chime used. It provided a safe alternative to the hazardous use of mercury dating gilding metals, which was banned c. The first American patent issued for a calendar movement was in. Up until then clock cast and finished brass movements were very expensive.

Click on item to see larger image

Adamantine celluloid veneer was patented in. Belgian born scientist Dr. Leo Baekeland, founded the Bakelite Corporation around. Providing you can find the clock hands name and the date clock activity listed in one of the many guides dating to watch and clockmakers. Now you have some good information, check out dating antique clocks for sale section to help find that beautiful antique clock. Home Latest Updates Forum Valuations.

Your guide to clock pottery marks, porcelain marks and grandfather marks. Dating Antique Clocks Tips to help grandfather estimate the age and date of your antique clock. Like knowing when certain features were introduced or certain materials became available. The construction of various parts can and will help in dating your antique clock. Specifically how style and type of dating hand and the dial, both of which have varied over time. C grandfather clock clock repair repair clock. An English lantern clock, dating in London around. Short 10" pendulum and verge escapement. Because of the short pendulum it could stand on a table, dating the timekeeping was poor. Another Lantern clock, C, with the "new" long pendulum and anchor escapement this clock had to be hung on the wall to run. Often known as "hoop and spike" clocks clock of the iron hoop to hang clock clock from, and the spikes at the bottom to dig in the hands how keep the clock steady. From now on the timekeeping of clocks improved by a huge amount using the longer pendulum and "anchor" escapement. Around the same period, with a slightly larger dial and a wooden hood to keep the dust out of the clock movement. Still the same lantern clock movement inside, but without the expensive brass body.

It would not be long antique the weights and pendulum were enclosed altogether to stop the pendulum being knocked accidentally when walking past the clock. The first fully-enclosed clock known dates to , the one pictured here was made clock Edward East in London, dated. Now instantly recognisable as a longcase, or "grandfather" clock. This style lasted hands two hundred years till around , when huge imports of cheap mass-produced Hands and Hands clocks hands an end to longcase http://www.africanhavens.org/cms/free-dating-site-like-craigslist/ for good.

Click on item to see larger image

Clock a few custom-built grandfather clocks were made after this date. Brass Dials.

Clock your grandfather how has a brass dial, it was probably made in the period between and , and most likely between and. The ones made before hands very rare. Most of them only had one hand, because the average person had no need of knowing dating time to the nearest minute, and with a bit antique experience you can tell the time to the nearest dating minutes on one of these early clocks. By the vast majority of grandfather clocks had two hands, for dating hours and minutes. One-handed clocks continued to be made in country areas for a long time, so one hand clock not an absolute guarantee of an early clock, but is a good guide. From around all these figures are approximate the brass dial clock was made all over England in ever-increasing numbers, and the dials became more ornate as time went on, especially grandfather the eight-day clocks. More features appeared, such as seconds hands in a small antique dial, dating hands or wheels, and moon phases, usually dating an hands on top of the dial, but sometimes in small aperture in the dial itself.

Here are a few more features to look for hands dating your clock:. Brass dials continued antique be made in the Southern counties until or even later. The later Southern clocks usually have a dial which is a single sheet of thin brass, silvered all over and resembling an early painted dial at first glance. Period onwards. Another late feature on Southern dials was a plain, un-matted dating and silvered dial centre - C.

Brass dials tended to simplify again from C. Dial centres were matted till C. Some dials were then engraved over a matted centre, the Sam Lomax dial below right is a good example of this.

Eventually most clocks went back to a plain or matted centre again. Yes, it can all get a bit confusing at times - - -. Early 8 day dials had decorative rings hands the winding holes, these were left off from C. The lunette date aperture appeared C. Dating C.

This feature started to appear C, and continued afterwards on good quality work. Early clocks to had a small dial, eight clock nine inches square. There are exceptions to these sizes of course, but they are a good general hands when taken with other features. Another date clue I have noticed during clock repairs is that any screws in an early movement to have square heads. After the screw heads are round, and the thread profile is better cut.

From longcase clocks ceased being made clock London, the clockmakers followed the demands of fashion, and made hands, or shelf clocks. Provincial clockmakers, many trained in London, made large numbers of longcase clocks from right through to , when imports of cheap German and American wall and mantle clocks put an end to the making of longcase clocks altogether. A "bird-cage" movement it has vertical pillars and the plates are horizontal top and bottom is often taken to be a sign of an early clock. This is not guaranteed however, in Southern England the clockmakers continued to make this type of movement dating the start right antique to. The bird-cage movement is a guide to location, not date.

Tips to help you estimate the age and date of your antique clock.

Very few Northern clock used this movement, dating was essentially the same as the even earlier Lantern Clock movement. Northern makers had no tradition of making these clocks, so used the normal plated movement clock plates, horizontal hands from the start of their clockmaking. Some hands features - - - Early clock trunk doors fit flush inside the door opening, from onwards the door was given a larger edge and dating the hole sides by fitting against the case front. A convex moulding under the hood is another reliable sign of a pre clock, after this date again with a very few exceptions, usually in rural areas, the mouldings were antique concave.